欧美久久成人I97精品国产91久久久久久久I性欧美1819sex性高播放I黄s视频I337p欧美I日韩在线观看免费I日韩成人精品中文字幕I久久国产乱子伦精品免费女,网站I夜夜视频欧洲I人妻va精品va欧美IAV综合一区I国产综合久久久7777777I一本色道久久I色婷婷精品久久二区二区I国产一级a -级I97视频总站I另类一区二区I迷情校园av

參考標準

標題

范圍

A-A-56032D

Commercial Item Description Ink, Marking, Epoxy Base

This commercial item description covers catalyzed epoxy system of marking inks for metallic or other non-porous surfaces and printed wiring boards,

ANSI / ISEA 105

American National Standard for Hand Protection Selection Criteria

This method covers the selection criteria for hand protection systems including chemical permeation, puncture resistance, and abrasion resistance.

ANSI / SAE Z26.1 (Abrasion Resistance, Plastics)

Safety Glazing Materials for Glazing Motor Vehicles and Motor Vehicle Equipment 

The purpose of this test is to determine whether the plastic has a certain minimum resistance to abrasion

ANSI / SAE Z26.1 (Abrasion Resistance, Safety Glass)

Safety Glazing Materials for Glazing Motor Vehicles and Motor Vehicle Equipment 

The purpose of this test is to determine whether safety glass has a certain minimum resistance to abrasion.

ANSI INCITS 322 (5.10 Bar Code Abrasion)

Card Durability Test Methods

The purpose of this test is to determine the extent of 1D bar code abrasion resistance

ANSI INCITS 322 (5.11 Magnetic Stripe Abrasion)

Card Durability Test Methods

The purpose of this test is to determine the extent of magnetic stripe abrasion resistance

ANSI INCITS 322 (5.9 Surface Abrasion)

Card Durability Test Methods

The purpose of this test is to provide a general means to produce controlled abrasion on a card surface

ANSI INCITS 322 (Image Abrasion)

Card Durability Test Methods

The purpose of this test is to determine the extent of image abrasion resistance

AS 2001.2.28

Methods of Test for Textiles

This standard sets out a method for the determination of the abrasion resistance of textile fabrics (applicable to all textile fabrics including coated and laminated fabrics, a method for wet testing is also specified).

AS/NZS 1580.403.2

Paints and Related Materials - Methods of Test

This Standard sets out a method for determining the abrasion resistance of a paint coating or other finishes, such as anodizing, electroplating, paper products, rubbers, plastics, textiles, glass and concrete.

AS/NZS 4266.20

Reconstituted Wood-Based Panels - Methods of Test

This standard specifies a method for determining the resistance to surface abrasion of decorative surfaces by using the Taber abrader.  It is applicable to all low pressure overlaid particleboards and medium density fibreboards (MDF's).

ASTM B607 (Appendix X2)

Standard Specification for Autocatalytic Nickel Boron Coatings for Engineering Use

This test method will evaluate the resistance of the coating to abrasive wear.

ASTM B733 (Appendix X1)

Standard Specification for Autocatalytic (Electroless) Nickel-Phosphorus Coatings on Metal

This test method will evaluate the resistance of the coating to abrasive wear.

Standard Specification for Hard-Coat Anodizing of Magnesium for Engineering Applications

ASTM C957

Standard Specification for High-Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane With Integral Wearing Surface

This specification describes the required properties and test methods for a cold liquid-applied elastomeric membrane for waterproofing building decks not subject to hydrostatic pressure. The specification applies only to a membrane system that has an integral wearing surface.

ASTM C1353

Standard Test Method Using the Taber Abraser for Abrasion Resistance of Dimension Stone Subjected to Foot Traffic

This test methods covers the establishment of an index of abrasion resistance by determination of loss of weight resulting from abrasion of dimension stone.

ASTM C1803

Standard Guide for Abrasion Resistance of Mortar Surfaces Using a Rotary Platform Abraser

This guide is intended to assist in establishing procedures for determining the relative resistance of treated or untreated mortar surfaces.

ASTM D1044

Standard Test Method for Resistance of Transparent Plastics to Surface Abrasion

This test method describes a procedure for estimating the resistance of Transparent Plastics to Surface Abrasion

ASTM D2205 (Section 18)

Standard Guide for Selection of Tests for Traffic Paints

This guide covers the selection and use of procedures for testing traffic paints in the laboratory and in the field.

ASTM D3389

Standard Test Method for Coated Fabrics Abrasion Resistance (Rotary Platform Double-Head Abrader)

This test method covers the determination of the resistance to abrasion of fabrics coated with rubber or plastics

ASTM D3451 (Section 22)

Standard Practices for Testing Polymeric Powders and Powder Coatings

These practices cover the selection and use of procedures for testing polymeric powders and powder coatings.

ASTM D3489 (Section 13)

Standard Test Methods for Microcellular Urethane Materials

ASTM D3730 (Section 10.1)

Standard Guide for Testing High-Performance Interior Architectural Wall Coatings

This guide covers the selection and use of test methods for high-performance interior architectural wall coatings (HIPAC) which differ form more conventional coatings in that they are tougher, more stain-resistance, more abrasion-resistant and, ordinarily, designed to be applied to wall surfaces of steel, masonry, and plaster or gypsum wallboard.

ASTM D3794 (Section 10.8.5.1)

Standard Guide for Testing Coil Coatings

This guide covers procedures for testing coil coatings. The test methods included are listed in Table 1. Where more than one test method is listed for the same characteristic, no attempt is made to indicate superiority of one method over another.

ASTM D3884

Standard Guide for Abrasion Resistance of Textile Fabrics (Rotary Platform, Double-Head Method)

This guide covers the determination of the abrasion resistance of textile fabrics using the rotary platform, double head tester (RPDH)

ASTM D4060

Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser

This test method covers the determination of the resistance of organic coatings to abrasion produced by the Taber Abraser on coatings applied to a plane, rigid surface, such as a metal panel.

ASTM D4685

Standard Test Method for Pile Retention of Corduroy Fabrics

This test method covers the determination of the loss of pile, specifically pile pull out, due to abrasion.

ASTM D4712

Standard Guide for Testing Industrial Water-Reducible Coatings

This guide covers the selection and use of procedures for testing water-reducible coatings, both pigmented and clear, utilizing synthetic lattices, synthetic resin emulsions, or water-reducible alkyds.

ASTM D5144 (Section 5.5.2)

Standard Guide for Use of Protective Coating Standards in Nuclear Power Plants

This guide provides a common basis on which protective coatings for the surfaces of light water-moderated nuclear power generating facilities may be qualified and selected by reproducible evaluation tests.

ASTM D5146 (Section 10.1.1)

Standard Guide to Testing Solvent-Borne Architectural Coatings

This guide covers the selection and use of procedures for testing solvent-borne coatings to be used on exterior, interior or both types of surfaces.

ASTM D5324 (Section 10.1.1)

Standard Guide for Testing Water-Borne Architectural Coatings

This guide covers the selection and use of procedures for testing water-borne coatings to be used on exterior, interior or both types of surfaces.

ASTM D6037 (Method A)

Standard Test Methods for Dry Abrasion Mar Resistance of High Gloss Coatings

Two test methods are included.  Test Method A uses a device that contains an abrasive wheel.  Test Method B uses a device that contains a wheel that has been fitted with abrasive paper.  Either method can be used to evaluate the dry abrasion mar resistance of coatings applied to planar, rigid surfaces.

ASTM D7255

Standard Test Method for Abrasion Resistance of Leather Rotary Platform, Double Head Method)

This test method covers the determination of the abrasion resistance of leather using the rotary platform, double-head tester (RPDH).

ASTM E1795

Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings

This specification covers minimum material performance and laboratory test procedures for non-reinforced liquid coating encapsulation products (single or multiple-coat systems) for leaded paint in buildings.

ASTM F1344 (Section 7.5)

Standard Specification for Rubber Floor Tile

This specification covers requirements for the compound and physical characteristics of rubber floor tile.

ASTM F1478

Standard Test Method for Determination of Abrasion Resistance of Images Produced from Copiers and Printers (Taber Method)

This test method describes a procedure for determining the amount of image abraded from the surface of a document.  This test method may be used to evaluate the abrasion resistance of images produced by business imaging products, including nonimpact printers, thermal transfer printers, and copiers.

ASTM F1978

Standard Test Method for Measuring Abrasion Resistance of Metallic Thermal Spray Coatings by Using the Taber Abraser

This test method quantifies the abrasion resistance of metallic coatings produced by thermal spray processes on flat metallic surfaces.  It is intended as a means of characterizing coatings used on surgical implants.

ASTM F2051 (Annex A1)

Standard Specification for Implantable Saline Filled Breast Prosthesis

This specification covers the requirements for single use saline inflatable, smooth and textured silicone shell implantable breast prostheses, intended for use in surgical reconstruction, augmentation, or replacement of the breast.

ASTM F2068 (Section 6.2.3)

Standard Specification for Femoral Prosthesis-Metallic Implants

This specification covers metallic stemmed femoral prosthesis used to replace the natural hip joint by means of hemi-arthroplasty or total hip surgical procedures.

ASTM G195

Standard Guide for Conducting Wear Tests Using a Rotary Platform Abraser

This guide covers and is intended to assist in establishing procedures for conducting wear tests of rigid or flexible materials utilizing the rotary platform abraser.

Australia Department of Civil and Environmental Engineering

Laboratory Tests for Strength, Hardness and Abrasiveness: Explanatory Notes.

Describes method of testing using Taber Abraser

Blu-Ray Disc (v1.2)

Blu-ray Disc Read-Only Format - Part 1: Basic Format Specifications

The entrance surface of the disc should have sufficient scratch resistance, which may be improved by a protective coating.

Boeing P.S. 13208

Hardcoating of Aluminum Alloys

This Specification provides the requirements and procedures for producing a hard oxide coating on aluminum alloys.  This coating provides excellent abrasion resistance for sliding wear applications, corrosion resistance, and electrical insulation.  Corrosion resistance can be increased by sealing the coating, but abrasion resistance is decreased.

BS 3900: Part E14

Paints and Varnishes; Determination of Resistance to Abrasion {Part 1: Rotating Abrasive-Paper-Covered Wheel Method}

This part of ISO 7784 specifies a method for determining the resistance to abrasion of a dried film of paint, varnish or related product, using abrasive paper attached to wheels and abrading by making a rotary movement

BS 3900: Part E15

Paints and Varnishes; Determination of Resistance to Abrasion {Part 2: Rotating Abrasive Rubber Wheel Method}

This part of ISO 7784 specifies a method for determining the resistance to abrasion of a dried film of paint, varnish or related product, using abrasive rubber wheels and abrading by making a rotary movement

BS 8204-3

Screed, bases and in situ floorings.  Polymer modified cementitious leveling screeds and wearing screeds. Code of Practice

BS AU 178a

Specification for Road Vehicle Safety Glass

Specifies requirements for safety glass for installation as windscreens, other windows, or as partitions in motor vehicles and trailers.  

BS EN 13672

Surfaces for sports areas - Determination of resistance to abrasion of non-filled synthetic turf

This document describes a method for the determination of the wear resistance of a non-filled synthetic turf surface using an abrasive wheel under laboratory conditions.  It is applicable to non-filled synthetic turf with a pile height greater than 15mm.

BS EN 60903

Live Working-Gloves of Insulating Material

Mechanical testing requirements.

CFFA-1 &200

Standard Test Methods - Chemical Coated Fabrics and Film

To determine the abrasion resistance of chemical coated fabrics and films using a rotary platform double head tester.

CFFA-P-101C

Recommend Minimum Performance Standards for Vinyl Swimming Pool Liners-In-Ground

This document sets forth recommended minimum performance standards for vinyl and other polymeric films, plain and printed, which are used as in-ground swimming pool liners.

CID A-A-56032

Military Specification - Ink, Marking, Epoxy Base

This specification covers a catalyzed epoxy system of marking inks for metallic or other non-porous surfaces.

CID A-A-59776

Gear, Fire Protective

This commercial item description covers the requirements for a structural fireman's coverall to be used by Navy damage control fire fighters.

CNS K6591

Method of Test for Polyurethane Athletic Installation Material

This standard covers the test method for polyurethane (PU) of athletic installation use.

CPA WR-01

Standard Test Method for the Evaluation of Wear Resistance of Laminated Decorative surfaces using Abrading Wheels

This test measures the ability of a laminated  decorative surface to resist abrasive wear-through of the decorative layer, utilizing a Taber rotary platform, double-head abraser equipped with abrading wheels.

CTS No. 5538

Abrasion Resistance Taber Abraser

This procedure covers the determination of the resistance of coatings to abrasion using the Taber Abraser

DIN 52 347

Testing of Glass and Plastics; Abrasion Test; Method Using Abrasion Wheels and Measurements of Scattered Light

in German

DIN 53 109

Testing of Paper and Board; Determination of  Abrasion by the Abrasion Wheel Method

in German

DIN 53 754

Testing of Plastics; Determination of Resistance of Wear by Abrasive Wheels

in German

DIN 53 799

Decorative Laminated Sheets on Basis of  Aminoplastic Resins; Test Method

in German

DIN 68 861 T2

Furniture Surfaces: Behavior at Abrasion

in German

DLA1

Determination of Resistance to Surface Wear

This Appendix specifies a method of measuring the ability of the surfaces of decorative laminated sheets to maintain their original design or colour under abrasive wear.

DPS 11.04

Hard Anodizing Aluminum

This process standard specifies procedures and requirements for hard anodizing aluminum alloys. It shall be used when specified on the Engineering drawing.

EN 13310

Kitchen Sinks - Functional Requirements and Test Methods

This standard specifies the functional requirements and test methods for domestic kitchen sinks, used in residential (domestic houses, guest houses and similar) premises. This standard does not specify aesthetic and dimensional requirements. It does not apply to industrial kitchen sinks. Note: All drawings are examples only; other forms are permissible.

EN 13329-Annex E

Laminate floor coverings - Elements with a surface layer based on amnioplastic thermosetting resins - Specifications, requirements and test methods

This annex specifies the method for measuring abrasion resistance and consequently determining the abrasion class of laminate floor covering elements.  The test described measures the ability of the surface layer to resist abrasive wear-through.

EN 13696

Wood flooring - Test methods to determine elasticity and resistance to wear and impact resistance

This document specifies two alternative test methods to determine the resistance to wear of lacquered wood floorings and one method to test the elasticity of the lacquer.

EN 14323

Wood-based panels-Melamine faced boards for interior uses-Test Methods

This test measures the ability of the decorative surface of melamine surfaces boards to resist abrasive wear-through by rotating a specimen in contact with cylindrical wheels covered with abrasive paper. The number of revolutions of the specimen required to cause a defined degrees of abrasion is used as measures of resistance to abrasion.

EN 14327

Leather - Physical and Mechanical Tests - Determination of Abrasion Resistance of Automotive Leather

This European Standard specifies a method of determining abrasion resistance of automotive leather

EN 14354-Annex D

Wood Based Panels - Wood Veneer Floor Covering

This method of test specifies  a procedure to determine the resistance to wear of lacquered wood veneer floor covering.

EN 14431

Vitreous and Porcelain Enamels- Characteristics of the enamel coatings applied to steel panels intended for architecture

EN 14688

Sanitary Appliances - Wash Basins - Functional Requirements and Test Methods

This European Standard specifies the functional requirements and test methods for wash basins for domestic purposes.

EN 14864

Vitreous and Porcelain Enamels - Enamel coatings applied to steel for writing surfaces- Specifications

EN 14904

Surfaces for Sports areas - Indoor surfaces for multi-sports use-Specification

This European Standard specifies requirements for surfaces for indoor facilities for multi-sports use. It also covers surface systems which include both their supporting and upper layers whether prefabricated, produced in situ or a combination of  the two. Not applicable to indoor tennis halls.

EN 438-2

Decorative High Pressure Laminates (HPL); Sheets  Based on Thermosetting Resins; Part 2: Determination of Properties

The test measures the ability of the decorative surface of the sheet under test to resist abrasive wear-through to the sub-layer.

EN 655

Resilient Floor Coverings-Tiles of agglomerated composition cork with polyvinyl chloride wear layer-Specification

This European standard specifies the characteristics of agglomerated cork with a wear layer based upon polyvinyl chloride and modification thereof.

EN 660-2

Resilient floor coverings - Determination of wear resistance - Part 2: Frick-Taber Test

This European Standard describes the Frick-Taber method for determining the wear resistance of the wear layer of polyvinyl chloride floor coverings under laboratory conditions.  The test method is applicable to floor coverings with smooth surfaces.  It can be used to determine the wear resistance of surfaces against abrasion and particularly for ranking different wear layer types within one type of product.

FDA Metallic Plasma Sprayed Coatings

Guidance for Industry on the Testing of Metallic Plasma Sprayed Coatings on Orthopedic Implants to Support Reconsideration of Postmarket Surveillance Requirements

This guidance document represents the agency's current thinking on the testing results that will enable FDA to reconsider the requirement for postmarket surveillance of plasma sprayed hip prostheses.

Fed. Specification TT-P-0091D

Interim Federal Specification - Paint, Rubber Base, Styrene-Butadiene Type, Interior, for concrete floors.

This specification covers a rubber-base paint for interior use on concrete floors.

Fed. Test Method Std. No. 191A Method 5306.1

Abrasion Resistance of Cloth: Rotary Platform, Double-Head (Taber) Method

This method is intended for determining the abrasion resistance of cloths in terms of percent change in breaking strength, or breaking strength after a given period of abrasion, or the number of abrasion cycles required to produce a specified state of destruction.  It is used to evaluate cloth durability.

Fed. Test Method Std. No. GG-P-455b

Plates and Foils, Photographic (Photosensitive Anodized Aluminum)

This specification covers the requirements for photosensitive anodized aluminum sheets and foils.  For purposes of this specification, foils as referred to in this specification is defined as material 0.010 inch and thinner

IKEA Spec. No. IOS-TM-0002

Surface Resistance-Test Methods

Description of a method that measures the ability of a coated surface to resist abrasive wear-through to the underlying substrate by assessing the resistance to liquid paraffin (fat) in the abraded area. The method is used on coated wood, foiled and laminated substrates in applications where high surface resistance is required.

IPC-TM-650 

Abrasion (Taber Method) Solder Mask and Conformal Coating

This method is designed to evaluate the resistance of solder mask or conformally surfaces to rubbing abrasion.

ISO 10074

Specifications for Hard Anodic Oxidation Coatings on Aluminum and its Alloys

This International Standard specifies requirements for hard anodic oxidation coatings on aluminum and its alloys, including test methods.

ISO 15082

Road Vehicles-Tests for rigid plastic safety glazing materials

Determination of whether the plastic, safety glazing material has a certain minimum resistance to abrasion at ambient temperature under dry or wet (car wash) conditions.

ISO 2046-Annex C

Effects of Surface Finish and Colour on Scratch Resistance

The test measures the ability of a decorative surface of the sheet under test to resist abrasive wear through to the sub-layer.

ISO 24338

Laminate Floor Coverings - Determination of Abrasion Resistance

This International Standard specifies the method for measuring abrasion of laminate floor covering elements.

ISO 3537

Road Vehicles - Safety Glazing Materials - Mechanical Tests

This International Standard specifies mechanical test methods relating to the safety requirements for all safety glazing materials in a road vehicle, whatever the type of glass or other material of which they are composed.

ISO 5470-1

Rubber or Plastics Coated Fabrics - Determination of Abrasion Resistance

This part of ISO 5470 describes a method of assessing the abrasive wear resistance of coated fabrics.

ISO 7784-1

Paints and Varnishes; Determination of Resistance to Abrasion

This part of ISO 7784 specifies a method for determining the resistance to abrasion of a dried film of paint, varnish or related product, using abrasive paper attached to wheels and abrading by making a rotary movement

ISO 7784-2

Paints and Varnishes; Determination of Resistance to Abrasion

This part of ISO 7784 specifies a method for determining the resistance to abrasion of a dried film of paint, varnish or related product, using abrasive rubber wheels and abrading by making a rotary movement

ISO 9352

Plastics; Determination of Resistance to Wear by Abrasive Wheels

This International Standard specifies a general method for determining the resistance to abrasive wear of plastics under the action of abrasive wheels.  It is equally applicable to moulded test specimens, components and finished products.

JC Penney - MTC-205

Abrasion Resistance of Textile Fabrics (Rotary -Platform, Double-Head Method)

To determine the abrasion resistance of textile fabrics using the rotary-platform double-head tester.

JC Penney - PPS# 303-03076

JCPenny Product Research & Technology Laboratories Product Performance Standard PPS# 303-0307 Luggage

Flat Abrasion, CS-17 wheels, 100g load, 5400 cycles

JIS A 1453

Method of Abrasion Test for Building Materials and Part of Building Construction (Abrasive-Paper Method)

This Japanese Industrial Standard applies to building materials and parts of building construction and specifies the testing method to evaluate the degree of abrasion of the test piece.

JIS H 8503

Methods of Wear Resistance for Metallic Coatings

This is a test to examine the wear resistance of metallic coatings.

JIS K 5600: Part 5, Section 8

Testing Methods for Paints {Part 5: Mechanical property of film -- Section 8: Abrasion resistance (Rotating abrasive paper covered wheel method)} 

This Standard is one of a series of standards dealing with the sampling and testing of paints, varnishes and related products. This Standard specifies a method for  determining the resistance to abrasion of a dried film of paint, varnish or related product, using abrasive rubber wheels and abrading by making a rotary movement.

JIS K 5600: Part 5, Section 9

Testing Methods for Paints {Part 5: Mechanical property of film -- Section 9: Abrasion resistance (Rotating abrasive rubber wheel method)} 

This Standard is one of a series of standards dealing with the sampling and testing of paints, varnishes and related products. This Standard specifies a method for  determining the resistance to abrasion of a dried film of paint, varnish or related product, using abrasive rubber wheels and abrading by making a rotary movement.

JIS K 6735

Plastic-polycarbonate sheet-type, size and characteristics

JIS K 6902

Testing Method for Laminated Thermosetting Decorative Sheets

This Japanese Industrial Standard specifies the testing method for laminated thermosetting decorative sheets.

JIS K 7204

Testing Method for Abrasion Resistance of Plastics by Abrasive Wheels

This Japanese Industrial Standard specifies the testing method for the abrasion resistance of plastics by abrading the test piece, particularly in, with an abrasive wheel.

JIS K6264

Rubber, Vulcanized or Thermoplastic - Determination of Abrasion Resistance - Part2: Testing Methods

This method specifies the testing methods for determination of abrasion resistance of rubber, vulcanized or thermoplastic (hereafter referred to as "vulcanized rubber").

JIS L 1018

Test Methods for knitted fabrics

JIS L 1021

Textile Floor Covering - Part 11: Determination of Wear

This Japanese Industrial Standard specifies the testing methods for determination of wool fiber integrity using an abrasion machine.

JIS L 1085

Test Methods for Non-Woven Interlining Fabrics

JIS L 1096

Testing for Woven Fabrics

This Japanese Industrial Standard specifies the testing methods for the evaluation of general characteristics of woven fabric foundation cloth.  

JNB 30.04.09

Abrasion Resistance of Printed Graphics

This test procedure is used to determine the abrasion resistance of decorative finishes/graphics, used within the vehicle interior.  The test shall be used to give an indication of the comparative wear characteristics of painted, printed or hot embossed finishes, to plastic substrates.  The test is used to determine the desired wear characteristics are met.

LAT-4-2200

Hard Anodizing

This method covers the requirements for anodization of aluminum and it alloys

MIL-A-8625F(1)

Military Specification - Anodic Coatings for Aluminum and Aluminum Alloys

This specification covers the requirements for six types and two classes of electrolytically formed anodic coatings on aluminum and aluminum alloys for non-architectural applications.

MIL-C-83409

Military Specification - Coatings, Visor, Polycarbonate, Flying Helmet

This specification covers the optical and durability requirements fro abrasion resisting coatings as applied polycarbonate visors conforming to MIL-V-43511.

MIL-DTL-15024F

Military Specification - Plates, Tags, and Bands for Identification of Equipment

This specification covers the materials and physical characteristics of plates, tags and bands (identification devices) used for identification of equipment.

MIL-DTL-19834C

Plates, Identification or Instruction, Metal Foil, Adhesive Backed - General Specification For

This specification covers adhesive-backed metal foil identification or instruction plates, herein referred to as identification plates, for use as internal and external equipment identification or instruction (see 6.1).

MIL-DTL-22992F

General Specification for Connectors, Plugs and Receptacles, Electrical Waterproof, Quick Disconnect, Heavy Duty Type

This specification covers multicontact heavy duty, quick disconnect, waterproof, electrical plug and receptacle connectors and associated accessories for electronic and electrical power and control circuits.

MIL-DTL-43511D

Detail Specification - Visors, Flying Helmet, Polycarbonate

This specification covers general and performance requirements for curved polycarbonate flyer's helmet visors worn by aircrew personnel.

MIL-DTL-43511D

Detail Specification - Visors, Flying Helmet, Polycarbonate

This specification covers general and performance requirements for curved polycarbonate flyer's helmet visors worn by aircrew personnel.

MIL-P-18493

Military Specification - Packing, Performed, Carbon; and Carbon Stock, Packing

This specification covers carbon packing material (1700) for rotary rod and shaft.

MIL-PRF-24613A  

Performance Specification - Deck Covering Materials, Interior, Cosmetic Polymer

This specification establishes the performance requirements for cosmetic deck covering materials to be applied either directly over primed or unprimed, clean steel and aluminum interior deck surfaces, or over deck covering underlay materials conforming to MIL-PRF-3135, that provide a wear resistant, low maintenance deck surface.

MIL-PRF-24712A

Military Specification - Coatings, Powder (Metric)

This specification covers powder coatings for interior steel, aluminum, copper-nickle and bronze equipment, furniture, and electrical box surfaces and on exterior steel, aluminum, copper-nickel, and bronze surfaces exposed to marine atmosphere, high humidity, seawater and weathering.

MIL-PRF-28800F

Military Specification - General Specification for Test Equipment for use with Electrical and  Electronic Equipment

This specification describes the general requirements for test equipment used in testing electrical and electronic equipment.

MIL-PRF-32170A

Performance Specification - Deck Tiles, Wear Resistant

This specification establishes the requirements for wear-resistant and fatigue reducing deck tile systems (including required adhesives and/or sealers) that are halogen free and require no floor finish used in Naval shipboard interior applications.

MIL-PRF-32171B

Performance Specification - Deck Coatings, High Durability

This specification establishes the requirements for high-durability, wear-resistant deck coatings for use in high-traffic areas, with minimal maintenance.

MIL-STD-13231C

Department of Defense Standard Practice - Marking of Electronic Items

This standard covers the general requirements for marking of electronic items.

MIL-T-53029C

Military Specification - Tanks, Fabric, Collapsible: 10,000; 20,000; And 50,000 Gallon, Drinking Water

This specification covers tanks, fabric, collapsible: 10,000; 20,000; and 50,000 gallon for drinking water storage, complete with fittings and repair items.

MIL-V-43511C

Military Specification - Visors, Flyer's Helmet, Polycarbonate

The abrasion resistance coating test shall be conducted in accordance with MIL-C-83409

NALFA LF-01

Laminate Flooring

This test measures the ability of the surface of laminate flooring to resist abrasive wear through the décor layer.

NASTA

Manufacturing Standards and Specifications for Textbooks

If offset printed on coated cover material, a protective top coating for abrasion resistance is required.

National Aircraft Standard NAS 1192

Performance Specification for Hard Anodic Coatings on Aluminum Alloys

This specification defines the performance requirements for hard anodic coatings on aluminum and aluminum alloy parts

NEMA LD3

High Pressure Decorative Laminates

This test measures the ability of the surface of high-pressure decorative laminate to resist abrasive wear-through of the decorative layer.

NF G 37-121

Rubber or Plastic Coated Fabric-Determination of the Wear Resistance by Rubbing with two Abrasive Wheels

(in French)

NF T30-015

Abrasion Resistance Test on Paint

(in French)

NHDOT Section 711

Preformed Retroreflective Pavement Marking Tape

Tape shall consist of glass spheres of a high optical quality imbedded into a binder on a suitable backing that is pre-coated with a pressure-sensitive adhesive.  

NHTSA 49 CFR 571.205

Glazing Materials

This standard specifies requirements for glazing materials for use in motor vehicles and motor vehicle equipment.

NIOSH CET-APRS-STP-0316

Standard Test Procedure for Determination of Haze, Luminous Transmittance, and Abrasion Properties of Primary Lens System Materials for Full Facepiece Respiratory Protective Devices (RPS)

The purpose of this test is to quantify the haze, luminous transmittance, and abrasion resistance properties of the primary lens material of a full facepiece RPD

Nokia DMXS1146-EN

Menu Paint Approval Testing Requirements

This document details the NMP best practice for the acceptance and verification of coatings and paint finishes applied to Nokia plastics for the Menu system.

NSF/ANSI 35

High Pressure Decorative Laminates for Surfacing Food Service Equipment

This Standard applies to high pressure decorative laminates for use as work and nonwork surfaces of food service equipment on which direct food contact during normal preparation or holding operations is not intended, expected, or reasonable. Applications of high pressure decorative laminates covered by this Standard include wait stations, service counters, and other counters when used in conjunction with cutting boards or other means of preventing direct food contact with the laminate. High pressure decorative laminates used on equipment for which other NSF or ANSI/NSF Standards or Criteria exist shall also comply with the applicable requirements therein.

NSF/ANSI 49

Class II (Laminar Flow) Biohazard Cabinetry

This Standard applies to Class II (laminar flow) biosafety cabinetry designed to minimize hazards inherent in work with agents assigned to biosafety levels 1, 2, 3, or 4 and defines the tests that shall be passed by such cabinetry to meet this Standard.

NSF/ANSI 51

Food Equipment Materials

This Standard is applicable to the materials and finishes used in the manufacture of food equipment (e.g., broiler, beverage dispenser, cutting board, stock pot). 

SAE AMS 2438

Chromium Coating: Thin, Hard, Dense Deposit

This specification covers the engineering requirements for the deposition of a thin, hard dense chromium coating on surfaces of ferrous and non ferrous alloys and the properties of the coating.

SAE AMS 2469G

Hard Anodic Coating Treatment of Aluminum and Aluminum Alloys Processing and Performance Requirements

This specification establishes the engineering requirements for producing a hard anodic coating on aluminum and aluminum alloys and the properties of such coating.

SAE J 1530

Test Method for Determining Resistance to Fiber Loss, Resistance to Abrasion and Bearding of Automotive Carpet Materials

This test method covers determination of abrasion resistance, fiber loss and bearding resistance of automotive carpet materials.

SAE J 1847

Abrasion Resistance Testing - Vehicle Exterior Graphics and Pin Striping

This SAE Recommended practice applies to the abrasion resistance testing of decorative tapes, graphics, and pin striping.  It may also have relevance to certain vehicle labels and plastic wood grain film.  The resistance to abrasive damage is judged qualitatively by its effect on the legibility, pattern, and color of the graphic marking.

SAE J 2394

Seven-Conductor Cable for Abs Power

This SAE Standard establishes the minimum construction and performance requirements for seven-conductor 1/8-2/10-4/12 cable for use on trucks and trailers.

SAE J 315

Surface Vehicle Standard-Fiberboard Test Procedure

This SAE provides  test methods for determining the critical characteristics of basic or finished fiberboard products. Where applicable, methods of tests developed by SAE and ASTM have been referenced.

SAE J 365

Method of Testing Resistance to Scuffing of Trim Materials

This test can be used to determine the resistance to scuffing of test specimens such as fiberboards, fabrics, vinyl coated fabrics, leathers, and similar trim materials.

SAE J 80

Automotive Rubber Mats

This SAE recommended practice covers the requirements for rubber floor mats made from five types of rubber compound as required by the physical property requirements of the application.

SAE J 948 

Test Method for Determining Resistance to Abrasion of Automotive Bodycloth, Vinyl, and Leather, and the Snagging of Automotive Bodycloth

The Taber method of test is applicable for determining the resistance to snagging and abrasion of automotive fabrics and/or vinyl-coated fabrics.

SIS 92 35 09

Floor Materials - Determination of Abrasion Resistance

This standard describes a method for the determination of the abrasion resistance of organic flooring materials when exposed to walking traffic of a revolving nature (point abrasion).  The method is not however suited to asphalt, textile carpeting, or unlacquered wood.

Tappi T 476

Abrasion Loss of Paper and Paperboard (Taber-type method)

The objective of this method is to determine the resistance of surfaces of paper and paperboard to the action of abrasion, either wet or dry, by measuring abrasion loss.  This test is not applicable to the surfaces treated with wax or similar materials which would fill in the pores of the abrasive wheels.

UN EN 48-250

Paint and Varnishes-Resistance to Abrasion-Taber Method

This norm specifies a method for the determination of resistance to abrasion for paints, varnishes and products when using the Taber Abraser.

UNE 56842

(translated) This norm applies to the furniture of kitchen or kitchen furniture elements just as supply themselves for their final use, not being valid to evaluate the characteristics of the coverings (laminated plastics or other) of independent form.  

UNE 57095

Paper and cardboard - Determination of Resistance to Abrasion - Taber Method

(translated) This norm intends to describe to the method of measurement of the sensitivity of the faces of paper or cardboard to the action of standardized surfaces abrasives, as much in humid as in dry, using the Taber apparatus.

UNI 9115

Furniture - Test for surface finishes - Behaviour of surfaces to wear abrasion.

(translated) It establishes a method in order to estimate the surface of furniture and is used to maintain the design, color or aspect and subject them to abrasive action.  The method is adapted in order to compare various finish, or as a control test in order to assure that a determined level of furniture surface performance is maintained and applied to all.

United Nations - ECE Regulation 43

Uniform Provisions Concerning the Approval of Safety Glazing Materials and their installation on Vehicles

This Regulation applies to safety glazing and glazing materials intended for installation as windscreens or other panes, or as partitioning, on power-driven vehicles and their trailers.

USIFI-DOC-001

Test Method Recommendations Coated and Laminated Fabrics

This document provides recommendations for test methods to be used in evaluating and characterizing coated and laminated fabrics for use in military applications.

USIFI-DTL-53308

Detail Specification Cloth and Strip, Laminated or Coated, Vinyl, Reinforced, High Strength, Flexible

This specification covers three types, four classes, and two forms of laminated or coated cloth.

USIFI-PRF-44423

Performance Specification Cloth, Flame Resistant, Light weight, Reversible

This specification covers a flame resistant, light weight, reversible cloth.

WSP 020.4.R3(12)  

Standard Test Method for Abrasion Resistance of Nonwoven Materials (Rotary Platform, Double-Head Method)

This method covers the determination of the abrasion resistance of nonwoven fabrics using the rotary platform, double-head tester (RPHD).